Polski
All Cattegories
-
Motorcycle
addremove
-
Body
addremove
-
Braking system
addremove
-
Steering system
addremove
-
Drive system
addremove
-
Exhaust system
-
Used parts
-
Motogadget
addremove
-
Clothes
addremove
-
Engine parts
-
3D prints
Cafe racer parts
There are 170 products.
Availability: 10 In Stock
As soon as an on-board voltage of 15.1 volts is exceeded for longer than 2 seconds, a warning flasher function is activated via the two blinker outputs and the additional LED output is switched on. In most cases, it is then sufficient to switch off the engine immediately to prevent major damage.
Availability: 9 In Stock
This cable kit allow you a fast and accurate build of your own bike harness. A 6 wire shielded cable allow a fast connection from the handle bar switches to your electronic box. The set comes with 30 cm shrink tube, 8 x 2 cm lettered shrink tube and 30 cable ties in 2 different sizes.
Availability: 18 In Stock
The small dimensions and the low weight of the electronic box devices allow in the most cases to fix the box with Velcro tape somewhere in the bike. However, for some rough situations we recommend to fix the box with this holder at the bike. The holder have 4 mm holes and a double sided sticky tape on the upper contact surface faced to the box, what prevent the box from unwanted moves if heavy vib
Availability: 9 In Stock
Please note that these inserts are only available for the European market.
Availability: 10 In Stock
The 4 solder pins on the rear side are connected as follow:
Availability: 10 In Stock
The reserve led for models up to 1985 is flashing when the fuel level is below 7 liter and it is continous on when the fuel level is below 4 liter. The housing is from a 3D printer and it's waterproof with epoxy glue potted.
Availability: 11 In Stock
Dimensions: 41 mm length x 26 mm wide x 12,5 mm height
Availability: 15 In Stock
Dimensions: 41 mm length x 26 mm wide x 12,5 mm height
Availability: 10 In Stock
An auto-cancel function is integrated into the module. The corresponding output flashes 4 times when a turn signal button is pressed briefly for less than 0.5 seconds and then switches off. This function can be used for overtaking. If the button is pressed for longer than 0.5 seconds, the output flashes 40 times. The auto-cancel function can be deactivated by connecting the green wire to ground.
Availability: 5 In Stock
An auto-cancel function is integrated into the module. The corresponding output flashes 4 times when a turn signal button is pressed briefly for less than 0.5 seconds and then switches off. This function can be used for overtaking. If the button is pressed for longer than 0.5 seconds, the output flashes 40 times. The auto-cancel function can be deactivated by connecting the green wire to ground.
Availability: 10 In Stock
An auto-cancel function is integrated into the module. The corresponding output flashes 4 times when a turn signal button is pressed briefly for less than 0.5 seconds and then switches off. This function can be used for overtaking. If the button is pressed for longer than 0.5 seconds, the output flashes 40 times. The auto-cancel function can be deactivated by connecting the green wire to ground.
Availability: 3 In Stock
A short press of a turn signal button (less than 0.5 seconds) for overtaking causes the corresponding turn signal to flash 4 times. A longer press (more than 0.5 seconds) causes the corresponding turn signal to flash 40 times. This auto-cancel function can be disabled by switching on the dip switch on the pcb.
Availability: 10 In Stock
The Rear Light EU is a module for Indian bikes with emergency flasher function. It converts the two signals from the original flasher / brake light combination in four separate outputs for brake light / rear light and indicators. A brakelight dim function is activated by default.
Availability: 3 In Stock
The E-Harness contain a dashboard control module and 2 power modules what control the 12 Volt power to all lights and other 12 Volt devices in a car. All switches and buttons at the dashboard are connected to the dashboard module. The modules "talk" via a small 2-wire data line. Almost all power outputs are short circuit protected and self resetting after the short circuit.
Availability: 4 In Stock
- 10 outputs with 10 Ampere maximum / each allow the control of the most loads in a car.
Availability: 10 In Stock
The Rear Light EU-C is a blinker splitter what converts the two signals from the original flasher / brake light combination and the center brake light in four separate outputs for brake light / rear light and indicators. 7 integrated led's allow a quick test while the installation. The 4 power outputs are short circuit protected.