Polski
Availability: 10 In Stock
You can also remove the marker light function of the BCM module if you wire the Marker Light X between BCM module and the indicators. This eliminate the marker light function of the indicators.
All Cattegories
-
Motorcycle
addremove
-
Body
addremove
-
Braking system
addremove
-
Steering system
addremove
-
Drive system
addremove
-
Exhaust system
-
Used parts
-
Motogadget
addremove
-
Clothes
addremove
-
Engine parts
-
3D prints
Cafe racer parts
There are 170 products.
Availability: 4 In Stock
The programming of a flasher mode is easy and will cost you about 30 seconds without the need to be a software specialist.
Availability: 3 In Stock
The Speed 2 Brake is an electronic brakeswitch what hang parallel to one of the original brakeswitches. The Speed 2 Brake have a speed sensor input what check a reduced speed and activate the brake light in case of a negative acceleration. The sensitivity is adjustable by 10 steps.
Availability: 10 In Stock
The Rear Light EU is a module for bikes with emergency flasher function. It converts the two signals from the original flasher / brake light combination in four separate outputs for brake light / rear light and indicators. A conversion of an US bike according to the requirements in the EU is much easier and less cost intensive with this new module.
Availability: 10 In Stock
The Rear Light EU-V is a module for vintage bikes w/o emergency flasher function. It converts the two signals from the original flasher / brake light combination in four separate outputs for brake light / rear light and indicators. A brakelight dim function can be activated.
Availability: 5 In Stock
Almost every bike what runs in US have a brake light / indicator combination in the way, that 2 lamps works as brake light and as indicator as well. This makes a conversion of an imported bike from Europe according to the requirements in the US a bit tricky. A conversion of an EU bike according to the requirements in the US is much easier and less cost intensive with the Rear Light US.
Availability: 10 In Stock
The activation of the module is made via a press on a button. Now you have 15 seconds time to put your rfid tag in front of the antenna. A red led on the antenna indicate the waiting state of the module. If the rfid tag is recognized then the led changes to blue color and the power for the bike is switching on. If the rfid tag is not recognized then the module fall back in sleep mode.
Availability: 10 In Stock
The speedometer is very easy to use: If the button is pressed and held down when the power supply is switched on, the wheel circumference appears on the display in cm and counts up between 50 cm and 220 cm until the button is released. The 4 LEDs on the outside indicate neutral, high beam, indicators and oil pressure.
Availability: 10 In Stock
The speedometer is very easy to use: If the button is pressed and held down when the power supply is switched on, the wheel circumference appears on the display in cm and counts up between 50 cm and 220 cm until the button is released. The 4 LEDs on the outside indicate neutral, high beam, indicators and oil pressure.
Availability: 10 In Stock
The speedometer is very easy to use: If the button is pressed and held down when the power supply is switched on, the wheel circumference appears on the display in cm and counts up between 50 cm and 220 cm until the button is released. The 4 LEDs on the outside indicate neutral, high beam, indicators and oil pressure.
Availability: 16 In Stock
The adjustment of the reserve level is easy: Just connect the module, fill the first required amount of gasoline in the tank and hold the green cable for a moment to ground / Minus. Now the module have store the first value. Then fill the next gasoline level in the tank and repeat the procedure and the module have stored the second fuel level.
Availability: 14 In Stock
The minimal indicator is a small microcontroller module and a 3 color led. The controller drives the different colors of the led and allows to indicate all necessary functions of your bike with just one led. Even 2 or 3 events at the same time can be indicated easily. The small dimensions of the module allows the implementation in the head light or even in the handle bar. You can indicate the foll
Availability: 10 In Stock
Care must be taken to ensure the correct position and alignment of the magnet during installation. The integrated LED helps to ensure correct alignment.
Availability: 10 In Stock
Dimensions left: 40 mm width x 50 mm height x 50 mm depth
Availability: 10 In Stock
- Press the button and switch on the ignition. The pump will start immediately.
Availability: 10 In Stock
This fuse box contains 6 separate outputs which switch off in the event of a short circuit and switch on again after the short circuit has been eliminated. 4 of the outputs have continuous positive and 2 outputs can be switched on or off via 2 buttons. This can be used to switch additional headlights, cell phone chargers, etc. In addition, the supply voltage is monitored and the outputs in the mod
Availability: 10 In Stock
The safety module check the 2 inputs for the neutral and sidestand switch and enables the start output when the neutral switch is closed, i.e. no gear is selected. The sidestand switch is also be checked. The ignition is switched off as long as a gear is engaged and the sidestand switch is open.