Polski
Availability: 6 In Stock
All Categories
-
Motorcycle
addremove
-
Body
addremove
-
Braking system
addremove
-
Steering system
addremove
-
Drive system
addremove
-
Exhaust system
-
Used parts
-
Motogadget
addremove
-
Clothes
addremove
-
Engine parts
-
3D prints
Touch 2 Switch XL
44 €
Dimensions: 40 mm x 25 mm x 12,5 mm
Safe shopping
Types of deliveries and payments:
[see details]
Complaints and returns:
[see details]
Guarantee safe & secure checkout
Touch 2 Switch XL
Sometimes there is only a need for 1-2 switch channels what don't require a complete control box. This electronic relay have 2 independent channels what are controlled by 2 momentary push buttons. Every press on a button will toggle the corresponding output between on and off. Each output can drive 240 Watt. The maximum power is 360 Watt per module. This allow the switch for additional headlights or other high current loads.
Maximum ambience temperature: 80 degree Celsius
DP9834
10 Items
Data sheet
- Manufacturer
- 27404 Rhade
Axel Joost Elektronik
Dipl.-Ing. Axel Joost
Germany
Selsinger Str. 28 - Dimensions
- 5 mm
5 mm
40 mm x 25 mm x 12
40 mm x 25 mm x 12 - Body material
- ABS with 2k epoxy resin potted
- Input voltage range
- 6 - 18 Volt
- Maximum temperature
- 80°C
80°C - Producent
- 27404 Rhade
Axel Joost Elektronik
Dipl.-Ing. Axel Joost
Germany
Selsinger Str. 28 - Maximum current
- 20 Ampere / output
- Maximum power
- 360 Watt / module
16 other products in the same category:
Availability: 10 In Stock
The speedometer is very easy to use: If the button is pressed and held down when the power supply is switched on, the wheel circumference appears on the display in cm and counts up between 50 cm and 220 cm until the button is released. The 4 LEDs on the outside indicate neutral, high beam, indicators and oil pressure.
Availability: 10 In Stock
The reserve led for models up to 1985 is flashing when the fuel level is below 7 liter and it is continous on when the fuel level is below 4 liter. The housing is from a 3D printer and it's waterproof with epoxy glue potted.
Availability: 20 In Stock
The Flasherbooster is connected between original flasher relay and your aftermarket indicators. It increase the supply voltages from the original flasher relay to 12 Volt and allow you to use your choice of aftermarket flashers at your bike. An integrated loadequalizer with 0,8 Watt load takes care for the correct flasher frequency in the most bikes.
Upper Triple Tree Clamp (Yoke) BMW K75 K100 RS RT LT (1982-1991) Cafe Racer -Mini+Motosign Mini LED
208 €
Availability: 3 In Stock
Availability: 2 In Stock
Availability: Out of stock
Availability: 5 In Stock
An auto-cancel function is integrated into the module. The corresponding output flashes 4 times when a turn signal button is pressed briefly for less than 0.5 seconds and then switches off. This function can be used for overtaking. If the button is pressed for longer than 0.5 seconds, the output flashes 40 times. The auto-cancel function can be deactivated by connecting the green wire to ground.
Availability: 16 In Stock
Availability: 9 In Stock
An auto-cancel function is integrated into the module. The corresponding output flashes 4 times when a turn signal button is pressed briefly for less than 0.5 seconds and then switches off. This function can be used for overtaking. If the button is pressed for longer than 0.5 seconds, the output flashes 40 times. The auto-cancel function can be deactivated by connecting the green wire to ground.
Availability: 10 In Stock
The Rear Light EU is a module for bikes with emergency flasher function. It converts the two signals from the original flasher / brake light combination in four separate outputs for brake light / rear light and indicators. A conversion of an US bike according to the requirements in the EU is much easier and less cost intensive with this new module.
Availability: Out of stock