Polski
Availability: 1 In Stock
All Categories
-
Motorcycle
addremove
-
Body
addremove
-
Braking system
addremove
-
Steering system
addremove
-
Drive system
addremove
-
Exhaust system
-
Used parts
-
Motogadget
addremove
-
Clothes
addremove
-
Engine parts
-
3D prints
Speedsensor
23 €
Care must be taken to ensure the correct position and alignment of the magnet during installation. The integrated LED helps to ensure correct alignment.
Safe shopping
Types of deliveries and payments:
[see details]
Complaints and returns:
[see details]
Guarantee safe & secure checkout
Speedsensor
The active speedometer sensor is based on the Infineon TLE4964 magnet chip. This enables maximum ranges of up to 1 cm to the magnet. A blue status LED is integrated, which enables visual control during alignment. A small tab allows it to be attached in various places. The housing comes from the 3D printer and measures 19 mm x 10.5 mm x 8.5 mm. The connection cable is 2 m long and a 5 mm magnet is included in the package.
Care must be taken to ensure the correct position and alignment of the magnet during installation. The integrated LED helps to ensure correct alignment.
DP9829
10 Items
Data sheet
- Manufacturer
- 27404 Rhade
Axel Joost Elektronik
Dipl.-Ing. Axel Joost
Germany
Selsinger Str. 28 - Dimensions
- 5 mm
5 mm
5 mm x 8
5 mm x 8
19 mm x 10
19 mm x 10 - Producent
- 27404 Rhade
Axel Joost Elektronik
Dipl.-Ing. Axel Joost
Germany
Selsinger Str. 28 - Included
- 5 mm magnet
- Cable length
- 2 m
- Maximum range to magnet
- 1 cm
16 other products in the same category:
Availability: Out of stock
Availability: 9 In Stock
Availability: 2 In Stock
Availability: 10 In Stock
The speedometer is very easy to use: If the button is pressed and held down when the power supply is switched on, the wheel circumference appears on the display in cm and counts up between 50 cm and 220 cm until the button is released. The 4 LEDs on the outside indicate neutral, high beam, indicators and oil pressure.
Availability: 52 In Stock
All you need to know:
- Material - made of durable stainless steel.
- Fixing - M6 bolt for secure attachment.
- Universal fit - compatible with all motorcycles.
- Positioning - adjustable design allows custom placement of brake reservoir on handlebar, master cylinder, or clutch.
- Versatility - ideal for stunt riders (concealed placement for tricks) and cafe racer builds (minimalist aesthetic).
- Braking system compatibility - designed for master cylinder setups.
Availability: 100 In Stock
Przełącznik ze stali nierdzewnej z gwintem 8 mm. Mały rozmiar pozwala na prawie niewidoczny montaż w kierownicy w połączeniu z modułem sterującym.
Availability: 5 In Stock
An auto-cancel function is integrated into the module. The corresponding output flashes 4 times when a turn signal button is pressed briefly for less than 0.5 seconds and then switches off. This function can be used for overtaking. If the button is pressed for longer than 0.5 seconds, the output flashes 40 times. The auto-cancel function can be deactivated by connecting the green wire to ground.
Availability: 4 In Stock
Mały moduł migający dla światła hamowania. Zwiększa bezpieczeństwo przez alarmowanie kierowców z tyłu. 14 trybów migania do wyboru.
Availability: 10 In Stock
The Rear Light EU-V is a module for vintage bikes w/o emergency flasher function. It converts the two signals from the original flasher / brake light combination in four separate outputs for brake light / rear light and indicators. A brakelight dim function can be activated.
Upper Triple Tree Clamp (yoke) BMW K1 K100 K1100 (1991-2002) RS RT LT Cafe Racer - Motogadget MINI
208 €
Availability: 2 In Stock
Availability: Out of stock
Availability: Out of stock
Availability: 236 In Stock
Przycisk chwilowy ze stali nierdzewnej z gwintem 8 mm. Bardzo mały, pasuje bezpośrednio do większości kierownic. Obsługa w rękawicach.
Availability: 1 In Stock