Polski
Availability: 4 In Stock
Mały moduł migający dla światła hamowania. Zwiększa bezpieczeństwo przez alarmowanie kierowców z tyłu. 14 trybów migania do wyboru.
All Categories
-
Motorcycle
addremove
-
Body
addremove
-
Braking system
addremove
-
Steering system
addremove
-
Drive system
addremove
-
Exhaust system
-
Used parts
-
Motogadget
addremove
-
Clothes
addremove
-
Engine parts
-
3D prints
Flasher Checker
72 €
If an indicator fails in subsequent operation, i.e. the current consumed falls below 20% of the normal operating current, the Flasher Checker activates the hazard warning function for as long as the flasher relay is activated. The hazard warning function switches off automatically when the flasher relay is deactivated.
Safe shopping
Types of deliveries and payments:
[see details]
Complaints and returns:
[see details]
Guarantee safe & secure checkout
Flasher Checker
After replacing the original indicators with LED indicators, the flashing frequency is often increased because the current drawn by the flasher relay or BCM has been greatly reduced. The Flasher Checker is simply clamped between the flasher relay and the indicators and monitors the performance of the indicators during operation. Programming is very simple: you connect the green cable to the left indicator input and the yellow cable to the right indicator input. The device then learns the normal operating current of the indicators during the first 5 flashing cycles.
If an indicator fails in subsequent operation, i.e. the current consumed falls below 20% of the normal operating current, the Flasher Checker activates the hazard warning function for as long as the flasher relay is activated. The hazard warning function switches off automatically when the flasher relay is deactivated.
Input voltage range: 7 - 18 Volt
DP9809
10 Items
Data sheet
- Manufacturer
- 27404 Rhade
Axel Joost Elektronik
Dipl.-Ing. Axel Joost
Germany
Selsinger Str. 28 - Dimensions
- 38 mm x 16 mm x 11 mm
38 mm x 16 mm x 11 mm - Body material
- ABS with 2k epoxy resin potted
- Input voltage range
- 7 - 18 Volt
- Producent
- 27404 Rhade
Axel Joost Elektronik
Dipl.-Ing. Axel Joost
Germany
Selsinger Str. 28
16 other products in the same category:
Adapter 4in1 Collector BMW K100 K1100 Cafe Racer Exhaust Muffler Kit Upgrade TUV Homologation Atest
146 €
Availability: 17 In Stock
Availability: Out of stock
Availability: 4 In Stock
Availability: 10 In Stock
The speedometer is very easy to use: If the button is pressed and held down when the power supply is switched on, the wheel circumference appears on the display in cm and counts up between 50 cm and 220 cm until the button is released. The 4 LEDs on the outside indicate neutral, high beam, indicators and oil pressure.
Availability: 9 In Stock
An auto-cancel function is integrated into the module. The corresponding output flashes 4 times when a turn signal button is pressed briefly for less than 0.5 seconds and then switches off. This function can be used for overtaking. If the button is pressed for longer than 0.5 seconds, the output flashes 40 times. The auto-cancel function can be deactivated by connecting the green wire to ground.
Availability: 10 In Stock
Dimensions: 41 mm length x 26 mm wide x 12,5 mm height
Availability: 13 In Stock
Availability: 3 In Stock
The Speed 2 Brake is an electronic brakeswitch what hang parallel to one of the original brakeswitches. The Speed 2 Brake have a speed sensor input what check a reduced speed and activate the brake light in case of a negative acceleration. The sensitivity is adjustable by 10 steps.
Two Battery Power Cables 2,5mm2 with Terminal - 60cm Cafe Racer Harley Davidson Stunt Harness...
15 €
Availability: 2 In Stock
Availability: 13 In Stock
Availability: 10 In Stock
The safety module check the 2 inputs for the neutral and sidestand switch and enables the start output when the neutral switch is closed, i.e. no gear is selected. The sidestand switch is also be checked. The ignition is switched off as long as a gear is engaged and the sidestand switch is open.
Availability: 56 In Stock
All you need to know:
- Easy Pull Mechanism - designed for effortless clutch operation.
- Compatibility - fits all motorcycles; requires a standard clutch cable on one side and connection to the clutch lever on the other.
- Color - anodised black for enhanced aesthetics and durability.
- Mounting options - three adjustable positions for cable attachment.
- Material - made from high-quality 6061 aluminum using CNC milling technology.
- Corrosion resistance - additional anodizing process for improved longevity.
Availability: 10 In Stock
The Rear Light EU-C is a blinker splitter what converts the two signals from the original flasher / brake light combination and the center brake light in four separate outputs for brake light / rear light and indicators. 7 integrated led's allow a quick test while the installation. The 4 power outputs are short circuit protected.
Availability: 10 In Stock