Automatic Daytime Runninglight Switch
    Automatic Daytime Runninglight Switch

Automatic Daytime Runninglight Switch

54 €
Dimensions: 38 mm x 16 mm x 11 mm
Quantity
Last items in stock

 

Safe shopping

  Types of deliveries and payments:

[see details]

  Complaints and returns:

[see details]

available payment methods

Guarantee safe & secure checkout

Delivery time shipment

Automatic Daytime running light switch

This electronic relay contains 2 power outputs what can drive 60 Watt / each. A daylight sensor detect if the ambience light is dark or bright and the device switch between daytime running light and low beam, depending of the ambience light. The switch time from daytime running light to low beam is immediately for situations when you ride from a bright place in a darker place. The switch time from low beam to daytime running light is adjusted to 3 seconds in order to get the light sensitivity down against light reflections. You can adjust and store the trigger value of the ambience light in 60 steps.

Sensor: 4,1mm LDR cell, front surface encapsulated against moisture

DP9805
2 Items

Data sheet

Manufacturer
27404 Rhade
Axel Joost Elektronik
Dipl.-Ing. Axel Joost
Germany
Selsinger Str. 28
Dimensions
38 mm x 16 mm x 11 mm
38 mm x 16 mm x 11 mm
Body material
Black ABS plastic
waterresist potted
Input voltage range
6 - 18 Volt
Producent
27404 Rhade
Axel Joost Elektronik
Dipl.-Ing. Axel Joost
Germany
Selsinger Str. 28
Maximum output power
60 Watt / output

16 other products in the same category:

B-Box
Quick view

B-Box

180 €
Availability: 8 In Stock
- Switch - output for parking light / Plate light / speedo etc.
Speed 2 Brake
Quick view

Speed 2 Brake

37 €
Availability: 3 In Stock
The Speed 2 Brake is an electronic brakeswitch what hang parallel to one of the original brakeswitches. The Speed 2 Brake have a speed sensor input what check a reduced speed and activate the brake light in case of a negative acceleration. The sensitivity is adjustable by 10 steps.
C-BS Harness
Quick view

C-BS Harness

299 €
Availability: 6 In Stock
The digital harness C-BS ("BS" stands for switches and buttons) for the bike control via push buttons and switches is an universal harness, what contain 2 small control boxes. The control boxes "talk" together via a thin serial bus cable. The switches, push buttons and power cables are wired direct to the nearest box. This reduces the amount of cables and the installation time significant in a typ
Evo Flasher 1
Quick view

Evo Flasher 1

69 €
Availability: 10 In Stock
An auto-cancel function is integrated into the module. The corresponding output flashes 4 times when a turn signal button is pressed briefly for less than 0.5 seconds and then switches off. This function can be used for overtaking. If the button is pressed for longer than 0.5 seconds, the output flashes 40 times. The auto-cancel function can be deactivated by connecting the green wire to ground.
Holder
Quick view

Holder

8 €
Availability: 18 In Stock
The small dimensions and the low weight of the electronic box devices allow in the most cases to fix the box with Velcro tape somewhere in the bike. However, for some rough situations we recommend to fix the box with this holder at the bike. The holder have 4 mm holes and a double sided sticky tape on the upper contact surface faced to the box, what prevent the box from unwanted moves if heavy vib
Rear Light US
Quick view

Rear Light US

108 €
Availability: 5 In Stock
Almost every bike what runs in US have a brake light / indicator combination in the way, that 2 lamps works as brake light and as indicator as well. This makes a conversion of an imported bike from Europe according to the requirements in the US a bit tricky. A conversion of an EU bike according to the requirements in the US is much easier and less cost intensive with the Rear Light US.